After months of testing and development TRE is proud to announce the release of its new TRE PR-1 carbon fibre aero body kit for BMW G80 M3 and G82 M4. The intention behind this product was not only to produce something fresh from an aesthetic stand point, but also to develop a kit that offers a refined fit and finish. Ensuring design elements from the G80 G82 are carried through and accentuated, the fitment from body to carbon is as flush as possible, with comprehensive mounting solutions which we will go into more detail. Produced from Pre-Preg Carbon Fibre this kit includes: Three-Piece Front Splitter Rear Spoiler Side Skirts PR-1 Splitter is a modular design with the best fitment. This splitter carries through the design language of the front bumper to create a deep aggressive look.TRE designed this splitter to counter the event of any damages, either side or front pieces can be replaced. Notice the perfect fitment of each piece which utilises a hidden bolt mounting system from underneath to ensure optimum strength and fixture. This splitter is designed from pre-preg carbon fibre, fits both BMW G80 M3 and G82 M4 using the OEM mounting points underneath the front bumper. Pros and Cons of installing this prooduct: Pros Easy installation. Utlises OEM mounting holes. Fits snug to the bumper for unmistakable location. Adds aggression to the front end. Cons Requires access underneath car to fit. Shop TRE PR-1 Splitter for G80 M3 G82 M4 PR-1 Spoiler The design of this rear spoiler follows the lines from the carbon factory roof humps to the boot lid, then following out to the tail lights. G80 and G82 variants differ in design slightly to suit. Notice how the rear spoiler almost merges seamlessly into the trunk on top and underneath, as well as meeting close to the outer edges of the boot. Designed and developed here in the UK from the ground up using inspiration from the CS and Performance styles. Following the success of the G87 M2 and G42 2 Series ID-01 Spoilers, the mission from TRE was to open this design to the G80 and G82 market. This spoiler is designed from pre-preg carbon fibre, with two variations, one for BMW G80 M3 and one for G82 M4 using 3M tape to simple stick onto the boot / trunk. Pros and Cons of installing this prooduct: Pros Easy installation. No tools required. Fits snug to the boot for unmistakable location. Adds aggression to the rear end. Cons Slight gap either side of spoiler will need aligning. Shop TRE PR-1 Spoiler for G82 M4 Shop TRE PR-1 Spoiler for G80 M3 PR-1 Side Skirts A clean, simple flat design that focus on widening the look of the car, working with the lines carried from the existing OEM gloss black side skirts and rear bumper design for visual cohesion. These side skirts are designed from pre-preg carbon fibre, fit both BMW G80 M3 and G82 M4 using the OEM mounting points underneath the sills. Pros and Cons of installing this prooduct: Pros Easy installation. Utlises OEM mounting holes. Fits snug to the body for unmistakable location. Adds width to the car. Cons Requires access underneath car to fit. Shop TRE PR-1 Side Skirts for G80 M3 G82 M4 What makes TRE so good? All TRE products feature the same high-quality pre-preg carbon fibre standards you would find with OEM level carbon fibre products. This means it's the lightest, strongest and highest quality manufacturing method possible. Every TRE product follows a 3 stage quality control verification process at the factory, then a fourth quality control final finish check before we package your order.
After months of testing and development TRE is proud to announce the release of its new TRE PR-1 carbon fibre aero body kit for BMW G80 M3 and G82 M4. The intention behind this product was not only to produce something fresh from an aesthetic stand point, but also to develop a kit that offers a refined fit and finish. Ensuring design elements from the G80 G82 are carried through and accentuated, the fitment from body to carbon is as flush as possible, with comprehensive mounting solutions which we will go into more detail. Produced from Pre-Preg Carbon Fibre this kit includes: Three-Piece Front Splitter Rear Spoiler Side Skirts PR-1 Splitter is a modular design with the best fitment. This splitter carries through the design language of the front bumper to create a deep aggressive look.TRE designed this splitter to counter the event of any damages, either side or front pieces can be replaced. Notice the perfect fitment of each piece which utilises a hidden bolt mounting system from underneath to ensure optimum strength and fixture. This splitter is designed from pre-preg carbon fibre, fits both BMW G80 M3 and G82 M4 using the OEM mounting points underneath the front bumper. Pros and Cons of installing this prooduct: Pros Easy installation. Utlises OEM mounting holes. Fits snug to the bumper for unmistakable location. Adds aggression to the front end. Cons Requires access underneath car to fit. Shop TRE PR-1 Splitter for G80 M3 G82 M4 PR-1 Spoiler The design of this rear spoiler follows the lines from the carbon factory roof humps to the boot lid, then following out to the tail lights. G80 and G82 variants differ in design slightly to suit. Notice how the rear spoiler almost merges seamlessly into the trunk on top and underneath, as well as meeting close to the outer edges of the boot. Designed and developed here in the UK from the ground up using inspiration from the CS and Performance styles. Following the success of the G87 M2 and G42 2 Series ID-01 Spoilers, the mission from TRE was to open this design to the G80 and G82 market. This spoiler is designed from pre-preg carbon fibre, with two variations, one for BMW G80 M3 and one for G82 M4 using 3M tape to simple stick onto the boot / trunk. Pros and Cons of installing this prooduct: Pros Easy installation. No tools required. Fits snug to the boot for unmistakable location. Adds aggression to the rear end. Cons Slight gap either side of spoiler will need aligning. Shop TRE PR-1 Spoiler for G82 M4 Shop TRE PR-1 Spoiler for G80 M3 PR-1 Side Skirts A clean, simple flat design that focus on widening the look of the car, working with the lines carried from the existing OEM gloss black side skirts and rear bumper design for visual cohesion. These side skirts are designed from pre-preg carbon fibre, fit both BMW G80 M3 and G82 M4 using the OEM mounting points underneath the sills. Pros and Cons of installing this prooduct: Pros Easy installation. Utlises OEM mounting holes. Fits snug to the body for unmistakable location. Adds width to the car. Cons Requires access underneath car to fit. Shop TRE PR-1 Side Skirts for G80 M3 G82 M4 What makes TRE so good? All TRE products feature the same high-quality pre-preg carbon fibre standards you would find with OEM level carbon fibre products. This means it's the lightest, strongest and highest quality manufacturing method possible. Every TRE product follows a 3 stage quality control verification process at the factory, then a fourth quality control final finish check before we package your order.
After months of testing and development TRE is proud to announce the release of its new TRE PR-1 carbon fibre aero body kit for BMW G80 M3 and G82 M4. The intention behind this product was not only to produce something fresh from an aesthetic stand point, but also to develop a kit that offers a refined fit and finish. Ensuring design elements from the G80 G82 are carried through and accentuated, the fitment from body to carbon is as flush as possible, with comprehensive mounting solutions which we will go into more detail. Produced from Pre-Preg Carbon Fibre this kit includes: Three-Piece Front Splitter Rear Spoiler Side Skirts PR-1 Splitter is a modular design with the best fitment. This splitter carries through the design language of the front bumper to create a deep aggressive look.TRE designed this splitter to counter the event of any damages, either side or front pieces can be replaced. Notice the perfect fitment of each piece which utilises a hidden bolt mounting system from underneath to ensure optimum strength and fixture. This splitter is designed from pre-preg carbon fibre, fits both BMW G80 M3 and G82 M4 using the OEM mounting points underneath the front bumper. Pros and Cons of installing this prooduct: Pros Easy installation. Utlises OEM mounting holes. Fits snug to the bumper for unmistakable location. Adds aggression to the front end. Cons Requires access underneath car to fit. Shop TRE PR-1 Splitter for G80 M3 G82 M4 PR-1 Spoiler The design of this rear spoiler follows the lines from the carbon factory roof humps to the boot lid, then following out to the tail lights. G80 and G82 variants differ in design slightly to suit. Notice how the rear spoiler almost merges seamlessly into the trunk on top and underneath, as well as meeting close to the outer edges of the boot. Designed and developed here in the UK from the ground up using inspiration from the CS and Performance styles. Following the success of the G87 M2 and G42 2 Series ID-01 Spoilers, the mission from TRE was to open this design to the G80 and G82 market. This spoiler is designed from pre-preg carbon fibre, with two variations, one for BMW G80 M3 and one for G82 M4 using 3M tape to simple stick onto the boot / trunk. Pros and Cons of installing this prooduct: Pros Easy installation. No tools required. Fits snug to the boot for unmistakable location. Adds aggression to the rear end. Cons Slight gap either side of spoiler will need aligning. Shop TRE PR-1 Spoiler for G82 M4 Shop TRE PR-1 Spoiler for G80 M3 PR-1 Side Skirts A clean, simple flat design that focus on widening the look of the car, working with the lines carried from the existing OEM gloss black side skirts and rear bumper design for visual cohesion. These side skirts are designed from pre-preg carbon fibre, fit both BMW G80 M3 and G82 M4 using the OEM mounting points underneath the sills. Pros and Cons of installing this prooduct: Pros Easy installation. Utlises OEM mounting holes. Fits snug to the body for unmistakable location. Adds width to the car. Cons Requires access underneath car to fit. Shop TRE PR-1 Side Skirts for G80 M3 G82 M4 What makes TRE so good? All TRE products feature the same high-quality pre-preg carbon fibre standards you would find with OEM level carbon fibre products. This means it's the lightest, strongest and highest quality manufacturing method possible. Every TRE product follows a 3 stage quality control verification process at the factory, then a fourth quality control final finish check before we package your order.