ADRO Carbon Rear Spoiler Tesla Model S Plaid Facelift II Pre-Preg Carbon Fibre Rear Spoiler by Adro (2021+)

ADRO Pre-Preg Carbon Fibre Rear Spoiler for Tesla Model S Facelift II (2021+)

The Model S boot lid asks for the lightest possible touch | anything too tall disrupts the silhouette; anything too subtle disappears. ADRO's Carbon Fibre Rear Spoiler lands exactly where it should: a restrained ducktail that lifts the rear deck just enough to complete the car's profile and give the back end the resolution the factory lid leaves open.

Construction is genuine pre-preg carbon fibre, autoclave-cured with a tight 2x2 twill weave. Pre-preg manufacturing means the resin and cloth are bonded under heat and pressure rather than applied by hand | the finished part is lighter, stiffer and more dimensionally consistent than wet-laid carbon and the gloss has the depth that comes from density rather than lacquer buildup. Fitment was developed from a full 3D scan of the Model S boot lid and refined through CFD simulation | the lip angle and trailing-edge profile are tuned to add measurable rear downforce and clean up air separation off the back of the car at speed.

Visually, the ducktail is present from a three-quarter angle and almost invisible head-on | the result of a design that prioritised resolution over drama. Installation uses the included 3M adhesive tape for a hardware-free finish that sits flush against the boot lid contour.

Key Features:

• Pre-preg carbon construction | autoclave-cured for superior strength-to-weight and tight tolerances
• 3D-scanned OEM fitment | designed from the actual boot lid contour for a flush, shimming-free fit
• CFD-developed profile | lip angle tuned to add rear downforce and reduce air separation at speed
• Restrained ducktail design | adds presence and aerodynamic resolution without overpowering the silhouette
• 3M adhesive tape included for clean, hardware-free installation

What's in the box:

• 1 x ADRO Carbon Fibre (pre-preg, 2x2 weave) Rear Spoiler
• 3M Adhesive Tape

NOTE: Not compatible with pre-2021 Model S (pre-facelift). Confirm factory spoiler configuration with team.

Q: What years of Tesla Model S does this spoiler fit?

A: This spoiler is confirmed for the Tesla Model S Facelift II (2021+). This covers the refreshed Model S with revised front and rear styling introduced in 2021 | including the Model S Plaid and Model S Long Range from that model year forward.

Q: What is the difference between pre-preg and standard carbon fibre?

A: Pre-preg carbon fibre starts with resin already evenly distributed through the fabric. The panel is then cured under heat and pressure in an autoclave, producing a part that is denser, lighter and more structurally consistent than wet-lay carbon, where resin is applied by hand. The gloss of pre-preg is also deeper and more uniform. It is the construction method used in Formula 1 and aerospace components.

Q: Does the ADRO spoiler produce measurable aerodynamic benefit?

A: Yes. The spoiler's lip angle and trailing-edge profile were developed through CFD simulation using 3D scan data of the Model S boot lid. The shape adds rear downforce and trims air separation off the back of the car, which translates to improved planted feel during fast lane changes and motorway driving.

Q: How is the spoiler fitted | does it require drilling?

A: No drilling is required. The spoiler uses the included 3M automotive adhesive tape for a clean, hardware-free installation. The 3D-scanned fitment means it sits flush against the boot lid contour without shimming or trimming.

Q: Is this spoiler compatible with Tesla's built-in rear spoiler (if optioned from factory)?

A: This spoiler is designed for the standard factory boot lid without the Tesla optional spoiler fitted. Contact info@autoid.co to confirm fitment for your specific configuration.

Q: Can AUTOID fit this spoiler?

A: Yes. AUTOID offers professional fitting at our Chelmsford, Essex facility. Contact info@autoid.co to book an appointment.